UL 5334 450°C Mica Fiberglass Wire for Vietnam and Indonesia — Compact Routing 600V AWM Style 5334

UL 5334 450°C Mica Fiberglass Wire for Vietnam and Indonesia

UL 5334 is a mica tape insulated wire with a fiberglass outer covering, rated 450°C and 600V AC under UL AWM Style 5334, produced under UL Follow-Up Service File No. E333030. UL 5334 occupies the same 450°C / 600V specification position as UL 5107 and UL 5335 — all three styles use mica tape as the primary insulation material and are rated for the same maximum continuous temperature and voltage — but the outer covering construction differs in a way that is practically significant for a specific category of routing application inside high-temperature equipment.

UL 5107 and UL 5335 use a glass braid outer covering — a round cross-section woven glass fibre braid that encases the mica-insulated conductor in a cylindrical protective layer. UL 5334 uses a fiberglass outer covering — a construction where the fiberglass is applied in a flat, layered or wrapped format rather than a round braid, producing a wire with a flatter overall cross-section and a more uniform, lower-profile outer surface than the glass braid construction at the same AWG and insulation thickness. The practical consequence of this construction difference is that UL 5334 can be routed through narrower gaps and flatter conduit cross-sections than UL 5107 at the same current-carrying conductor size, and lies flatter against surfaces when routed along panel walls and structural members inside furnace enclosures.

Vietnam and Indonesia’s industrial heating equipment sector — assembling tunnel kilns for ceramics, continuous annealing furnaces for glass and metal, industrial dryers for textile and food processing, and flat panel heater assemblies for a wide range of thermal processing applications — regularly encounters routing geometry constraints inside the equipment structure where the standard round glass braid mica wire profile does not fit. Vietnamese and Indonesian furnace and kiln builders specify UL 5334 dây mica sợi thủy tinh (mica fiberglass wire) for these compact routing applications. CableApex exports UL 5334 factory-direct CIF Ho Chi Minh City and CIF Surabaya from Yangzhou.

Product Specifications — UL 5334

UL 5334 vs UL 5107 vs UL 5335 — Construction Comparison

Applications in Vietnam and Indonesia

Kiln car internal wiring — tunnel kiln assemblies (Vietnam — Bình Dương ceramics sector)

Vietnam’s large ceramics manufacturing sector in Bình Dương province operates tunnel kilns where ceramic products are loaded onto kiln cars — wheeled refractory platforms that travel through the heated tunnel on rails. The kiln car structure carries electrical connections for some kiln designs — heating element connections routed through the car’s refractory body, or temperature measurement points on the car surface that transmit signal data through sliding contact connections at the car underframe. The structural channels and conduit paths built into the kiln car refractory body are typically narrow rectangular or oval cross-sections rather than round conduit — designed to minimise the thermal mass of the car structure while accommodating the minimum necessary wiring routing.

UL 5334 fiberglass mica wire fits into these narrow rectangular routing channels where a round glass braid wire of the same AWG would not — the flat fiberglass profile allows the wire to be routed through the same narrow rectangular slot that was designed for the flat profile, without the diameter penalty of the glass braid construction. Vietnamese kiln builders specifying dây mica sợi thủy tinh for kiln car internal routing use UL 5334 at the appropriate AWG for the circuit current, confident that the 450°C mica insulation performance is identical to UL 5107 while the flat fiberglass construction solves the routing geometry constraint.

Flat panel heater assembly wiring (Indonesia — industrial equipment manufacturing)

Indonesian industrial heating equipment manufacturers — in Bekasi, Tangerang, and Surabaya industrial zones — assemble a significant volume of flat panel infrared heater and resistive heater assemblies for use in industrial drying, curing, and heat treatment applications. These flat panel heater assemblies consist of heating elements mounted on a flat refractory or insulation board backing, with internal wiring routed flat against the panel surface from the element terminals to the connection terminals at the panel edge. The wire routing on the flat panel surface requires a wire construction that lies flat without the round profile of a glass braid wire lifting off the panel surface or creating a gap between the wire and the panel face at routing clips and cable ties.

UL 5334 fiberglass mica wire — kabel mica serat kaca in Indonesian procurement terminology — provides both the 450°C / 600V mica insulation performance required for the heated panel environment and the flat fiberglass profile that allows the wire to be routed flush against the panel face. Indonesian flat panel heater OEMs specify UL 5334 for the panel internal wiring to ensure that the wire assembly lies within the panel thickness envelope when the panel is installed in the equipment enclosure, without the glass braid round profile creating installation clearance problems at the panel mounting points.

Narrow conduit and insulation panel penetrations (Vietnam and Indonesia)

Industrial furnaces and kilns in Vietnam and Indonesia route internal wiring through penetration points in the furnace insulation panels and refractory wall sections — holes or slots cut through the furnace lining at the design stage to allow wiring to pass from the external connection panel into the heated chamber. The diameter or cross-section of these penetration points is determined at the furnace design stage and cannot be enlarged during operation without disrupting the furnace insulation integrity. When heating element replacement or rewiring is carried out on an operating furnace, the replacement wire must fit through the existing penetration points in the furnace insulation.

Where the existing penetration slots were cut with a flat profile — or where the slot has been worn to a flat oval cross-section by years of wire movement during element replacement cycles — UL 5334 fiberglass mica wire is the specification that can be threaded through the existing slot without requiring the slot to be enlarged. The flat fiberglass profile allows UL 5334 to pass through the same slot opening that a round glass braid wire would jam in, enabling element replacement without furnace insulation rework.

Ceramic refractory lining wiring channels (Vietnam — industrial kilns)

Ceramic refractory linings in Vietnamese industrial kilns are fabricated from fired refractory bricks and blocks with cast or cut channels for wire routing — channels whose cross-section geometry is determined by the refractory design and the available casting tools at the time of kiln construction. These channels are frequently rectangular or trapezoidal in cross-section, designed to accommodate a specific flat wire profile. UL 5334 fiberglass mica wire matches the flat cross-section profile expected by refractory channel designs that were specified for flat wire, allowing the wire to be seated fully in the channel with the refractory cap or cover piece closing flush over the wire without the protruding round profile of a glass braid wire preventing the cap from seating correctly.

Additional applications across Vietnam and Indonesia

• Conveyor tunnel oven heating zone internal wiring — flat profile routing along oven belt support structure in Vietnamese food processing factories
• Flat ceramic heater plate wiring — Vietnamese and Indonesian industrial heating element manufacturing
• Infrared heating panel internal element connections — Indonesian industrial drying and curing equipment
• Refractory-lined pipe heater internal wiring — Vietnamese petrochemical and chemical processing facilities
• Compact wiring harness assemblies in multi-zone flat furnace constructions — Indonesian industrial equipment OEM assembly

Key Features

Ordering Information

Specify AWG, conductor type (nickel-plated recommended for sustained 450°C operation), and quantity. MOQ 500 m per AWG. Mixed AWG orders accepted. UL 5334 compliance documentation and RoHS Declaration supplied with every order. For standard round cross-section routing at the same 450°C / 600V specification, see UL 5107. Sample from 10 m.

Why CableApex for Vietnam and Indonesia

CableApex manufactures UL 5334 mica fiberglass wire under UL Follow-Up Service File No. E333030 in Yangzhou, China. Factory-direct export to Vietnam and Indonesia — CIF Ho Chi Minh City or CIF Surabaya, 10–14 day transit. Full UL compliance documentation for equipment OEM qualification and maintenance procurement. No distributor margin on factory-direct orders. Contact us within 24 hours.

Please enable JavaScript in your browser to complete this form.

Company Name

Email Full Phone

Full Name *

Work Email *

Phone / WhatsApp

Request a Quote